|
An alkyd based topcoat for both exterior and interior use. This product is part of a complete system which is certified not to spread surface flames. Pilot II bases are intermediates and need tobe processed before use.
Technical Data
PILOT II
Product description
Pilot II is an alkyd based topcoat for both exterior and interior use. This product is part of a complete
system which is certified not to spread surface flames. Pilot II bases are intermediates and need to
be processed before use.
Recommended use
Topcoat in a traditional alkyd system suitable for steel and woodwork. Good weather and colour
stability. Good hiding power.
Film thickness and spreading rate
Minimum Maximum Typical
Film thickness, dry (µm) 30 50 40
Film thickness, wet (µm) 60 105 85
Theoretical spreading rate (m²/l) 16 9,6 12
Approvals
APAS approved to specification 2922.
Physical properties
Colour According to colour card and Multicolor tinting system (MCI)
Solids (vol %)* 48 ± 2
Flash point 36ºC ± 2 (Setaflash)
VOC 410 gms/ltr UK-PG6/23(97). Appendix 3
Gloss Glossy
Gloss retention Good
Water resistance Limited
Abrasion resistance Fair
Flexibility Good
*Measured according to ISO 3233:1998 (E)
Surface preparation
All surfaces should be clean, dry and free from contamination. The surface should be assessed and
treated in accordance with ISO 8504.
Coated surfaces
Clean, dry and undamaged compatible primer. Please contact your local Jotun office for more
information.
Other surfaces
The coating may be used on other substrates. Please contact your local Jotun office for more
information.
Condition during application
The temperature of the substrate should be minimum 3ºC above the dew point of the air,
temperature and relative humidity measured in the vicinity of the substrate. Good ventilation is
usually required in confined areas to ensure correct drying.
Application methods
Spray Use airless spray or conventional spray
Brush Recommended for stripe coating and small areas, care must be taken to achieve the
specified dry film thickness.
Roller May be used. However when using roller application care must be taken to apply
sufficient material in order to achieve the specified dry film thickness.
Application data
Mixing ratio (volume) Single pack.
Thinner/Cleaner Jotun Thinner No. 2
Guiding data airless spray
Pressure at nozzle 15 MPa (150 kp/cm², 2100 psi)
Nozzle tip 0.38 - 0.53 mm (0.015 - 0.021")
Spray angle 40 - 80°
Filter Check to ensure that filters are clean.
Drying time
Drying times are generally related to air circulation, temperature, film thickness and number of coats,
and will be affected correspondingly. The figures given in the table are typical with:
* Good ventilation (Outdoor exposure or free circulation of air)
* Typical film thickness
* One coat on top of inert substrate
Substrate temperature 5°C 10°C 23°C 40°C
Surface dry 5 h 4 h 3 h 1 h
Through dry 25 h 14 h 7 h 3 h
Dry to recoat, minimum 36 h 18 h 16 h 12 h
Dry to recoat, maximum 1
1. The surface should be dry and free from any contamination prior to application of the subsequent
coat.
The given data must be considered as guidelines only. The actual drying time/times before recoating
may be shorter or longer, depending on film thickness, ventilation, humidity, underlying paint system,
requirement for early handling and mechanical strength etc. A complete system can be described on
a system sheet, where all parameters and special conditions could be included.
Typical paint system
Alkydprimer or Pilot Primer 2 x 40 µm (Dry Film Thickness)
Pilot II 1 x 40 µm (Dry Film Thickness)
Other systems may be specified, depending on area of use
Storage
The product must be stored in accordance with national regulations. Storage conditions are to keep
the containers in a dry, cool, well ventilated space and away from source of heat and ignition.
Containers must be kept tightly closed.
Handling
Handle with care. Stir well before use.
Packing size
5 litre container
or
20 litre container
Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated
conditions. Do not breathe or inhale mist. Avoid skin contact. Spillage on the skin should immediately
be removed with suitable cleanser, soap and water. Eyes should be well flushed with water and
medical attention sought immediately.
For detailed information on the health and safety hazards and precautions for use of this
product, we refer to the Material Safety Data Sheet.
DISCLAIMER
The information in this data sheet is given to the best of our knowledge based on laboratory testing and
practical experience. However, as the product is often used under conditions beyond our control, we
cannot guarantee anything but the quality of the product itself. We reserve the right to change the given
data without notice.
Jotun is a World Wide company with factories, sales offices and stocks in more than 50 countries. For your
nearest local Jotun address please contact the nearest regional office or visit our website at www.jotun.com
ISSUED 2 APRIL 2007 BY JOTUN
THIS DATA SHEET SUPERSEDES THOSE PREVIOUSLY ISSUED | 
